Starter motor 4. Main fuse 5. Ignition switch 6. Secondary fuses 7. Voltage regulator 8. Magneto flywheel 9. Speed sensor Instrument panel MODE button Page 58 Vespa Primavera - i. Starter button Starter relay coil High beam warning light Light switch Headlight relay Headlight Saddle opening actuator Horn button Horn Engine oil pressure warning light Page 59 Vespa Primavera - i.
Page 60 Vespa Primavera - i. HORN 6. Page 61 Vespa Primavera - i. Page 62 Vespa Primavera - i. Page 63 Vespa Primavera - i. COIL - To reach it, remove the helmet compartment. Page 64 Vespa Primavera - i. Page 65 Vespa Primavera - i. Page 66 Vespa Primavera - i. Page 67 Vespa Primavera - i. On the left side of the chassis, under the footrest, there is the chassis-engine ground lead "C". Electrical system installation Front side 1. Page 68 Vespa Primavera - i.
Left control lock 3. Headlight connector 4. Instrument panel connector 5. Right control lock 6. Right stop button 7. Left electrical controls connector 8. Ignition switch 9. Voltage regulator Turn indicator control device Page 69 Vespa Primavera - i.
Voltage regulator connector Front left turn indicator connector Horn connections Saddle opening switch connector Page 70 Vespa Primavera - i. Headlight relay base Front right turn indicator connector Secondary fuses Page 71 Vespa Primavera - i. Right electrical controls connector Injection ECU Immobilizer aerial Page 72 Vespa Primavera - i.
Ground point on chassis Negative battery pole Diagnostics socket Positive battery pole Main fuse To rear cable harness Pre-installation for anti-theft device Saddle opening actuator connector Page 73 Vespa Primavera - i. Starter relay Roll-over sensor connector Page 74 Vespa Primavera - i. Engine temperature sensor connector 2.
Injector connector 3. Oxygen sensor connector 4. Magneto flywheel connector 5. Starter motor positive 6. Starter motor negative 7. Throttle body position sensor connector 8. Page 75 Vespa Primavera - i. Battery 4. Injector Engine speed sensor Engine temperature sensor Lambda probe Throttle body position Page 76 Vespa Primavera - i. Magneto flywheel Stop light Page 77 Vespa Primavera - i. Secondary fuses 9. Engine oil pressure sensor Page 78 Vespa Primavera - i.
Page 79 Vespa Primavera - i. Page 80 Vespa Primavera - i. Turn indicator control Turn indicator switch Left turn indicator bulbs Turn indicators warning lights Page 81 Vespa Primavera - i. License plate light Roll-over sensor Immobilizer LED Page 82 Vespa Primavera - i.
Injection ECU Checks and inspections Immobiliser The electronic ignition system is controlled by the control unit with the integrated Immobilizer system. Page 83 Vespa Primavera - i. The engine was located to the right of the drive wheel and was closed by a convex stamped casing.
To the left for symmetry, the same casing was made under which a spare wheel was placed. The gas tank was in the back of the scooter. The first Vespa was very technological in manufacturing and therefore cheap and quickly gained popularity.
In , a cc motor with a capacity of 4 liters was put on scooters. No license was purchased. S Operation and Maintenance Manual. Vespa G. S Service Repair Manual. S Service Station Manual.
Workshop Manual. Vespa Scooters Wiring Diagrams. Vespa PX Comments: 0. Vespa Primavera Operation and Maintenance Manual. How do I convert miles into kilometres?
What is the difference between E10 and E5 petrol? E10 petrol consists of up to ten per cent ethanol while E5 petrol will contain less than five per cent ethanol. As a result, the percentage of E10 petrol is lower than that of E5 petrol, making it less bad for the environment. How do I remove rust from my Vespa Scooter? Soak the rusty part in vinegar until completely soaked through. Let the vinegar work on the rust for 24 hours. Remove the rust with a wire brush or aluminium foil.
Is the manual of the Vespa Ciao available in English?
0コメント