Page 53 Select the line interface to be used. This section explains how to adjust or set the items in the menus and gives a brief introduction to the menus. Identifying the Home Menu The Home menu is displayed on the monitor screen when the system is turned on and has not been connected to a remote party.
The Camera menu is used to adjust the camera angle or brightness, or to preset the camera adjustments and to move the camera to the preset position. Page Phone Book The menu is used to check the incoming call and outgoing call histories or to call a remote party from the history list. History menu IP Page 60 7 Volume The volume-level bar is temporarily shown when you adjust the volume of the Communication System.
Using the Menus Page Operation Using The Menu Operation Using the Menu The basic operation through the menu is explained taking manual brightness adjustment in the Camera menu as an example. The Camera menu appears. The chapter is intended to be read by the system administrator. Registering Local Information Before connecting, set up the local system using the Setup menus.
This section describes how to display the Setup menus and gives a introduction to the menus. The Setup menu appears on the monitor screen. Menus available from a setup menu The Setup menus are grouped into the following depending on the setting items. The selected setup menu appears. Registering Local Information Page Answer Setup Menu When the local system is used as the main connected.
Page Communication Setup Menu When there is only one terminal connected, the display switches to full screen regardless of the Communication IP: Mode selection of the setting. Page 76 presentation data shares bandwidth with Communication SIP: Mode camera images that are also being sent.
This setting allows you to select how much of the Communication Bit Rate total bandwidth to use for H. Page 81 Monitor Output Blanking Period Allows you to select the video signal output Allows you to select the blackout period that from the Communication System. Communication System. Using the gatekeeper allows you to dial User Alias using the user name or user number as well Enter the user name H.
Page Tos Setup Menu audio communication is interrupted depending on a network status. The A1 to C2 or A1 to F2 fields appear. Sub-addresses can only be composed of boxes. Off: Does not display the volume meter. In this case, the memory of the Line Interface Disabled: Does not require the password Disabled: Does not require the password when saving the QoS setup settings.
Page 98 Annotation 64Kbps: Streams and records video at 64 Kbps. Display Terminal Name. The selected display appears. Displaying the Machine Status For details on configurations, consult with the system administrator.
Page Lan Connection With H. Note Do not enter the first 0 of the area code. Page About The Network Routing Check Before connecting a remote system, you can check the network routing to assure smooth connection with the system. For the network routing check, knowledge of network is required. Consult your network administrator or Sony dealer. If you have any questions about the checked result, consult your network administrator or Sony dealer. Page Chapter 3: Basic Connection Chapter 3: Basic Connection This chapter describes how to connect to a remote party after the administrator has completed various registrations and settings for the system.
The Home menu appears on the monitor screen and the picture shot by the local camera also appears. The menu screen will change according to the item you select. Now you can start communication with the remote party. Page Enter the host name and domain name ex. Note The unit is set to manual answer mode under factory default settings.
Ringing stops, and the connection is canceled. Up to remote parties can be registered in the Phone Book. To connect to the remote party by entering all the ISDN line numbers used, you can set the connection without using the bonding function of this system. The modification is completed. The group name input menu appears. The submenu appears. For detailed configuration, consult your network administrator.
The display switches to the Shared Phone Book. The volume level indicator appears on the monitor screen. Page Adjusting The Camera Adjusting the Camera You can adjust the image shot by the local camera that is sent to the remote party to obtain the desired angle and size. During communication you can also control the camera on the remote site to adjust the image shot by the remote camera. The selected camera pans and tilts, then the adjusted picture will be displayed in the small window or in full screen.
Pressing the b button increases the brightness, and pressing the B button decreases it. Page During communication pressing the F1 button on the Remote Commander switches between the camera on the local site and that on the remote site. When two cameras are connected, pressing the F2 button on the Remote Commander switches between the first and second cameras. The selected camera is shown at the top of the Camera menu. The Preset Save menu is restored.
You can adjust various items for camera adjustment. To focus on a distant subject, press the b button. To focus on a near subject, press the B button. The Video Input menu disappears. The stored video input is not deleted even after the system is turned off, and is selected when the power is turned on again.
This enables you to check how your own party is monitored on the remote site. Page Switches the monitored picture between the remote and local sites. Each press of the F1 button on the Remote Commander swaps the location of both pictures. Capturing the Screen To make a multipoint connection, see Chapter 6.
Page Streaming A Communication Streaming a Communication By broadcasting a stream of a visual communication, people who cannot attend the communication can watch the proceedings over the Web using a computer. Before broadcasting a live stream, be sure to configure the live stream permission setting. For details on viewing a streamed communication, see Chapter 7.
The saved data can then be viewed on a computer. Bamboo is a trademark. Drawing: Allows you to write letters or graphics on the screen. Page Operations during drawing Operate using the function keys on the tablet and the buttons on the pen. To stop drawing Press the second key from the top on the tablet. Page If you want to obtain the drawing rights, press the second key from the bottom on the tablet. The indicator Drawing executed by the local party appears on the monitor screen, and you are allowed to write letters and graphics on the screen.
If you do either, extreme noise and echo may be heard temporarily by the remote party. The same is true if the 8-meter microphone cable is used in the middle of the connections. Up to four microphones are powered by the AC adaptor, counting from the microphone connected to the AC adaptor. This is convenient for taking minutes of the communication. To connect the video equipment for input The Communication System is equipped with two video inputs. The picture from the selected equipment is displayed.
Page Pictures displayed on the two monitors During communication, the following images are displayed on the two monitors. Picture displayed on the first monitor The local or remote picture shot by the camera moving picture is monitored on the first monitor connected to the HDMI OUT connector. For details on each control, consult your Sony dealer. Page Chapter 5: Encrypted Connection Chapter 5: Encrypted Connection When a strictly confidential communication is required, the communication system enables a connection with encrypted video and audio.
A connection conducted using this feature is known as an encrypted connection. This chapter describes how to conduct an encrypted connection. The Communication System is equipped with standard encryption, which complies with the H.
Page Encrypt Priority Connects only to remote parties with standard encrypted connection enabled. Connect with encryption Local system: Remote system: Standard encrypted connection available Standard encrypted connection available Do not connect Local system: Remote system: Standard encrypted connection available Standard encrypted connection unavailable Preparing for an Encrypted Connection via LAN Page Starting An Encrypted Connection Starting an Encrypted Connection You can start an encrypted connection by calling a remote party in the same manner as a daily connection.
During an encrypted connection, the encryption icon, , is displayed. Note If there is no icon displayed, transmitted and received data are not encrypted. Confirm if an icon is displayed before starting a connection. Starting an Encrypted Connection If you have already made a point-to-point connection when a third point calls, the system automatically starts multipoint connection. To connect with a normal phone When you are using an ISDN connection, a normal phone can be connected at up to five points.
Page To register a multipoint connection list in the Phone Book The basic procedure for registration is the same as when registering a remote party for a point-to-point connection.
Page Enter all the parties to which you want to make a multipoint connection. Page To call remote parties not registered in the Phone Book Basic operations are the same as those for a point-to-point connection. The system begins dialing the remote parties selected in step 3.
Disconnect All: Cancels all the connections and restores the Home menu. Redial: Redials the numbers of the points that you failed to connect. Note on multipoint videoconferences using ISDN If the number of remote points connected increases as a result of dialing from the main terminal while making a multipoint connection using ISDN, some of Page Broadcast Modes And Displayed Windows indicating the terminal of the displayed picture also appears.
The indicator is displayed on the monitor screen while the local picture is broadcast. Broadcast Modes and Displayed Windows The chart described below shows the window displayed on the monitor screen when you select one of the broadcast modes.
Using the Display Control When is my volume too loud? A volume above 80 decibels can be harmful to hearing. When the volume exceeds decibels, direct damage can even occur. The chance of hearing damage depends on the listening frequency and duration. Can bluetooth devices of different brands be connected to each other? Yes, bluetooth is a universal method that allows different devices equipped with bluetooth to connect to each other.
What is bluetooth? Bluetooth is a way of exchanging data wirelessly between electronic devices via radio waves. The distance between the two devices that exchange data can in most cases be no more than ten metres.
What is HDMI? An HDMI cable is used to transport audio and video signals between devices. How can I best clean my Hi-Fi system? A slightly damp cleaning cloth or soft, dust-free cloth works best to remove fingerprints.
0コメント